K-BKR STAN DOP VA
Stainless steel ball valves, double-acting actuator
Product image
![K-BKR STAN DOP VA K-BKR STAN DOP VA](/data/img/product/00051363_0.jpg)
![K-BKR STAN DOP VA - data/img/product/00042441_0.jpg data/img/product/00042441_0.jpg - K-BKR STAN DOP VA](/data/img/product/00042441_0.jpg)
Properties
Design |
Pneumatic actuators, in double- or single acting version, with integrated end-position feedback |
Operating pressure |
max. 63 bar (depending on temperature and nominal size) |
Operating temperature |
-20 °C to +70°C |
Angle of rotation |
90 ° |
Standardised interfaces |
Interface actuator / valve: four or eight threaded holes in the drive housing according to EN ISO 5211, Interface actuator / S |
Pilot pressure |
5.5 bar |
Valve adapter |
Acc. to NAMUR |
Drive |
aluminium eloxed |
Drive seal |
NBR |
Ball valve |
Stainless steel 1.4401,with ISO-flange plate |
Ball valve seal |
PTFE |
Description
2-way cock, 3-piece, full bore
Note
Further information on request
Item
![](/images/up.gif)
Sort upwards
Sort downwards
![]() |
DN | Thread | A (mm) |
B (mm) |
D (mm) |
L (mm) |
AF (mm) |
---|---|---|---|---|---|---|---|
K- 07 30 02 42 | 15 | Rp 1/2 | 133,0 | 144,0 | 24,0 | 75,0 | 29 |
K- 07 30 02 43 | 15 | Rp 1/2 | 116,0 | 135,0 | 24,0 | 75,0 | 29 |
K- 07 30 02 44 | 20 | Rp 3/4 | 133,0 | 148,0 | 27,0 | 80,0 | 35 |
K- 07 30 02 45 | 20 | Rp 3/4 | 116,0 | 139,0 | 27,0 | 80,0 | 35 |
K- 07 30 02 46 | 25 | Rp 1 | 133,0 | 157,0 | 30,0 | 90,0 | 41 |
K- 07 30 02 47 | 32 | Rp 1 1/4 | 137,0 | 176,0 | 37,0 | 110,0 | 50 |
K- 07 30 02 48 | 40 | Rp 1 1/2 | 137,0 | 186,0 | 40,0 | 120,0 | 58 |
K- 07 30 02 49 | 50 | Rp 2 | 161,0 | 207,0 | 50,0 | 140,0 | 74 |
K- 07 30 02 50 | 65 | Rp 2 1/2 | 180,0 | 238,0 | 60,0 | 185,0 | 89 |
K- 07 30 02 51 | 80 | Rp 3 | 209,0 | 257,0 | 82,0 | 205,0 | 104 |
Disclaimer
Despite careful checking, we cannot guarantee the accuracy of all information included on this site, and we accept no liability.
All data and information in our online catalogue are based on currently valid standards and the regulations from the employer's liability insurance association. Product safety can only be guaranteed when our assembly instructions are carefully observed. Non-adherence to these regulations can affect product operation and functioning and result in a loss of warranty. Our warranty is only valid for HANSA-FLEX products. Our products are constantly subject to further development and technical changes are therefore possible.